Search:

Type: Posts; User: daujivar

Search: Search took 0.00 seconds.

  1. Unsolicited DNP3 Communication with Zenon 8.0

    Dear Support,&nbsp;<br><br>I am getting the unsolicited messages when my RTU connected to in ASE Tool as Master. However, I am unable to get the Unsolicited message frm same RTU in Zenon runtime v8.0...
  2. Double Click Acknowledge of alarm on Alarm Screen..!

    Dear Support,

    In one project, cutomer don't want to ack alarm on left Double click. However, double tap over alarm on Alarm Screen get acknowledges alarms !

    Using authorization, only disable...
  3. Replies
    2
    Views
    9,692

    Re: Disable double right click acknowledge

    Dear Support,

    I have tried this, However, double tap over alarm on Alarm Screen still get acknowledges alarms. The authorization only disable the Ack button available on side in same Screen.
    ...
  4. Version 7.0 To 7.11 - Dnp3 Driver Enhancement

    Dear Support,

    Thank-you for being there always. !!

    We are using 7.0 Version Build 9 of Zenon Energy & Supervisor in one of our project, protocol used are SNMP, DNP3. We are thinking to upgrade...
  5. Re: Message Control using COM Port in Zenon 7.11

    Dear Daniela,

    At Present I can not test with Diagnosis Viewer as we have test setup on site.

    Yes I am using GSM Modem for Message Control . I received an Event in event list that message...
  6. Message Control using COM Port in Zenon 7.11

    Dear Support,

    I have configured My Workspace, Project Specific Setting and Created the Function send Message as mention in the Manual.

    Also, I am able to test Connection with Modem(MOXA Model...
  7. Replies
    2
    Views
    8,041

    Re: Managing Users settings in Zenon Runtime

    Thank you Symeon. It Works.

    Regards
    Dauji
  8. Replies
    2
    Views
    8,041

    Managing Users settings in Zenon Runtime

    Hi All,

    Need your Advice to Achieve ...:confused::confused:

    At Present, I created Users in the Editor, and if I am Changing Password of these in Runtime or Creating New User, And Restarting...
  9. Replies
    5
    Views
    12,350

    Re: Runtime Exceeded

    Dear Ursula Piela,

    Thank you for the Response.

    I do not have any Interlock variables. I have to achieve this through response variable of command.

    I have IEC-61850 Protocol Driver in my...
  10. Replies
    5
    Views
    12,350

    Re: Runtime Exceeded

    Hello Support,

    Thank you for your Reply.

    But, I have notice that this stay until I restart my Run-time another time. Even Reload doesn't work for it !! what else can be the issue ?

    I have...
  11. Replies
    5
    Views
    12,350

    Runtime Exceeded

    Hello Support,

    During Testing in the Field in one of my Project, I have Received the following Message(in the Snap) during Command Processing. Although , I am able to control further, but the RED...
  12. Replies
    1
    Views
    7,901

    Variable diagnosis - Screen Type

    Hi Support,

    I am not able to use the diagnosis screen type for forcing the numeric value in simulation driver mode. ?

    Also, I am unable to set or use filter in any of the column of this screen...
  13. Replies
    1
    Views
    9,068

    Double Point Status Breaker & ALC

    Hello Support,

    I have a breaker whose open/close status are from 2 different Variable(Bool type). I am getting open(01) and Close(10) position correct and colour is getting transferred to line...
  14. Replies
    5
    Views
    11,655

    Re: DNP Driver Error...

    Thanks you Mark & Bernherd ..

    I will try this.. hope it solve my issue.

    Regards
    Dauji
  15. Replies
    5
    Views
    11,655

    Re: DNP Driver Error...

    Hi,

    I Am using the Zenon 7.0 SP0 Build0 .. So if I use Build 4 , will solve my Problem.. !!!!!

    Thanks

    Waiting for kind Reply

    Regards
    Dauji
  16. Replies
    5
    Views
    11,655

    DNP Driver Error...

    Hello Support.

    During My testing I got the following Error (Shown in attachment) while starting the Runtime.

    And these error will not be there .. if i uninstall and install the whole zenon...
  17. Replies
    1
    Views
    7,371

    Error Msg -Unlock Project from zenDB Admin

    Hi Support.

    I am facing a problem while creating a backup of a Project. Gives me a Error Msg as " Project Instance 'xxxx' is locked. you can unlock it from zenDB Admin."

    Can you please tell me...
  18. Replies
    4
    Views
    10,013

    Re: Zenon v7.0 OPC Server Version

    Thanks Mark for the Quick Reply...

    Regards
    DJ
  19. Replies
    4
    Views
    10,013

    Re: Zenon v7.0 OPC Server Version

    Hi Mark..

    Thanks for the Warm Welcome & Support. :)

    Please Correct me if I am Wrong, the Version is same for the Process GTW OPC DA Sever also.

    Right !!


    Thanks
  20. Zenon v7.0 Modbus Slave PROCESS GTW Limitation for Integration Projects

    Hello,

    In one of our Project, We have MB Slave - Master interface with the DCS where our Zenon7.0 is MB Slave and DCS is the MB Master. We have integration Project which have 3 Subproject. Zenon...
  21. Replies
    4
    Views
    10,013

    Zenon v7.0 OPC Server Version

    Hi,

    I would like to know which DA Version(s) does Zenon OPC Server Support ?


    Thanks
    DJ
Showing results 1 to 21 of 21